AOpen DE7200 Series Instrucciones de operaciones Pagina 19
- Pagina / 167
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SAFETY
30 Sep 13 2-3
DE-7200VFDCentrifuge
WARNING! W
HILE OPENING AND CLOSING THE CENTRIFUGE COVER,
PERSONNEL MUST ENSURE THAT ALL BODY LIMBS AND ANY OTHER
ITEMS ARE CLEAR OF THE COVER GAP. TWO HANDS MUST BE USED,
WITH BOTH HANDS ON THE COVER HANDLES AT ALL TIMES. DERRICK
RECOMMENDS HAVING A HOIST AVAILABLE
IF ADDITIONAL ASSISTANCE
IS DESIRED DURING THE OPENING/CLOSING PROCEDURE.
Maintenance
DANGER! HIGH VOLTAGE! SHUT DOWN, LOCK OUT, AND TAG OUT
ELECTRIC POWER, AND ENSURE THAT EQUIPMENT HAS STOPPED
ROTATING BEFORE WORKING ON THIS EQUIPMENT.
WARNING! WHILE OPENING AND CLOSING THE CENTRIFUGE COVER,
PERSONNEL MUST ENSURE THAT ALL BODY LIMBS AND ANY OTHER
ITEMS ARE CLEAR OF THE COVER GAP. TWO HANDS MUST BE USED, WITH
BOTH HANDS ON THE COVER HANDLES AT ALL TIMES. DERRICK
RECOMMENDS HAVING A HOIST AVAILABLE IF ADDITIONAL ASSISTANCE
IS DESIRED DURING THE OPENING/CLOSING PROCEDURE.
DANGER! EXPLOSION HAZARD! BE CERTAIN THAT SURROUNDING
ATMOSPHERE IS CLEAR OF ALL POTENTIALLY EXPLOSIVE GASES BEFORE
OPENING CONTROL CABINET DOOR.
Storage
WARNING! CENTRIFUGE MAY BE DAMAGED BY STORING IN A HIGH
HUMIDITY ENVIRONMENT (GREATER THAN 50% RH). EQUIPMENT MUST BE
STORED IN A LOW-HUMIDITY ENVIRONMENT.
MATERIAL SAFETY DATA SHEETS (MSDS’S)
Material Safety Data Sheets (MSDSs) advise personnel of the properties and any possible
hazards associated with these materials. Emergency first aid procedures, special precautions,
emergency telephone number, and other relevant data are contained in the MSDSs. These
documents are prepared by the product manufacturers, which have sole responsibility for
accuracy of the information.
The MSDSs listed below apply to products used in the manufacture of the Derrick equipment.
Where shown, dates are current as of the publication date of this manual. The latest MSDSs may
be obtained from the product manufacturer.
- DE-7200 Centrifuge 1
- CONTENTS 5
- Section 6
- CONTENTS 7
- SECTION 1 - INTRODUCTION 9
- EQUIPMENT USE 10
- DESCRIPTION 10
- Rotating Assembly 11
- Drive Motors 12
- Control Cabinet 12
- Case and Base 13
- Vibration Switch 13
- MECHANICAL OPERATION 14
- CONTROL SYSTEM 15
- PRODUCT SUPPORT 16
- CONTACT INFORMATION 16
- SECTION 2 - SAFETY 17
- Equipment Handling 18
- Maintenance 19
- Storage 19
- MSDS’S (CONT’D) 20
- SECTION 3 - INSTALLATION 21
- STORAGE 22
- Rotating Assembly and Motors 22
- INSTALLATION SEQUENCE 23
- EQUIPMENT HANDLING 24
- EQUIPMENT HANDLING (CONT’D) 26
- Liquid Discharge 29
- Solid Discharge Chute 29
- EQUIPMENT LEVELING 29
- FEED AND FLUSH CONNECTIONS 31
- COMPRESSED AIR 33
- FEED PUMP 33
- ELECTRIC POWER CONNECTIONS 33
- Connection Options 33
- POLARITY TEST 36
- SENSOR CONNECTIONS 37
- MACHINE STARTUP 38
- GENERAL 39
- SOFTWARE VERSION 39
- OPERATING SAFETY 39
- Purge System Bypass 40
- INITIAL STARTUP 41
- INITIAL STARTUP (CONT’D) 42
- OPERATING INSTRUCTIONS 43
- NORMAL STARTUP 44
- COLD CLIMATE STARTUP 45
- OPERATION 45
- Bowl Speed 47
- Conveyor Differential Speed 47
- Pond Depth 47
- Pond Depth (Cont’d) 48
- BEARING TEMPERATURES 50
- MOTOR TORQUE TREND 50
- SYSTEM DIAGNOSTICS 51
- PERFORMANCE STATUS 51
- ALARM AND FAULT MESSAGES 52
- VFD STATUS 53
- VFD STATUS (CONT’D) 54
- PUMP VFD FAULT STATUS 54
- VFD TEMPERATURE TRENDS 55
- VFD FAULT RESET 55
- VFD FAULT RESET (CONT’D) 56
- SETUP SCREEN 56
- PUMP SETUP SCREEN 57
- CLEAN OUT 57
- CLEAN OUT (CONT’D) 58
- Automatic Cleanout 58
- Manual Cleanout 58
- NORMAL SHUTDOWN 59
- AUTOMATIC SHUTDOWN 59
- Excessive Vibration 59
- Main Bearing Temperatures 59
- Excessive Bowl Speed 60
- Conveyor Clutch Trip 60
- EMERGENCY SHUTDOWN 61
- Electric Power Shutdown 61
- Mechanical Shutdown 61
- SECTION 5 - MAINTENANCE 63
- PREVENTIVE MAINTENANCE 64
- LUBRICATION CHART 65
- GEARBOX OIL LEVEL CHECK 65
- GEARBOX OIL CHANGE 66
- DRIVE BELT REPLACEMENT 67
- PURGE SYSTEM 69
- Bypassing Purge System 69
- Initial Purge Time Setting 70
- Leakage Compensation Test 71
- Rotating Assembly Removal 73
- Cleaning and Inspection 75
- Installation 76
- RECOMMENDED SPARE PARTS 77
- TROUBLESHOOTING 79
- Troubleshooting Procedure 79
- TROUBLESHOOTING (CONT’D) 80
- Troubleshooting Chart 80
- CONTROL COMPONENT INDICATORS 98
- MAINTENANCE 100
- DE-7200VFDCentrifuge 103
- CONTROL ENCLOSURE ASSEMBLY 141
- DE-7200 EX-PROOF 460/480/60/3 141
- 16472-00-002 141
- DE-7200 EX-PROOF 380/400/3 143
- 16472-00-003 143
- DE-7200 EX-PROOF 575/600/60/3 145
- 16472-00-004 145
- DE-7200 460/480/60/3 147
- 16472-00-005 147
- PURPOSE 149
- DE-7200VFDCentrifuge 150
- INSTALLATION 156
- HMI Server Installation 156
- Electric Power Connections 156
- Ethernet Connections 157
- Appendix A-HMIServerSystem 158
- OPERATING HMI SERVER 159
- Startup and Shutdown 159
- Operation 159
- Operation (Cont’d) 160
- REFERENCE DRAWINGS 164
Relacionado con productos y manuales para Barebones Pc / Estación De Trabajo AOpen DE7200 Series
(11 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales