AOpen DE7200 Series Instrucciones de operaciones Pagina 23
- Pagina / 167
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
INSTALLATION
01 Jan 14 3-3
DE-7200VFDCentrifuge
INSTALLATION SEQUENCE
Following is the sequence of steps for installing the centrifuge. The sequence presented may vary
depending on the user’s facilities and previous experience with this type of equipment.
1. Read and understand all safety information in Section 2 before installing and operating this
equipment.
2. Read and understand the equipment handling procedures in this section before lifting and
positioning the equipment.
3. Position and level equipment at installation site.
4. Remove shipping components, and lower and secure the rotating assembly bearing pillow
blocks to the base.
5. Adjust drive belt (refer to Section 5).
6. Connect liquid discharge line.
7. If discharge duct is to be used, connect duct to solids discharge chute.
8. Install flexible joint, feed tube, and piping connections for slurry feed, polymer injection, fresh
liquid cleanout, and sampling port.
9. Select and install feed pump.
10. Connect electric power supply to the equipment, and connect bowl motor, conveyor motor,
and feed pump motor to terminal blocks inside control cabinet.
11. Connect sensor cable to sensor junction box.
12. For explosion-proof cabinet, connect compressed air supply source to purge unit.
13. Refer to Section 4 for startup and operating procedures.
REQUIRED CLEARANCES AND POSITIONING
Sufficient space should be provided around the equipment to facilitate access for maintenance,
inspection, and adjustment.
Typical operation and maintenance functions include the following activities:
1. Access and operate the system control panel.
2. Open and close the control cabinet door (Figure 3-1).
3. Open and close top cover.
4. Grease rotating assembly bearings.
5. Check and fill gearbox.
6. Connect and disconnect feed and liquid discharge lines.
7. Remove and install feed tube.
- DE-7200 Centrifuge 1
- CONTENTS 5
- Section 6
- CONTENTS 7
- SECTION 1 - INTRODUCTION 9
- EQUIPMENT USE 10
- DESCRIPTION 10
- Rotating Assembly 11
- Drive Motors 12
- Control Cabinet 12
- Case and Base 13
- Vibration Switch 13
- MECHANICAL OPERATION 14
- CONTROL SYSTEM 15
- PRODUCT SUPPORT 16
- CONTACT INFORMATION 16
- SECTION 2 - SAFETY 17
- Equipment Handling 18
- Maintenance 19
- Storage 19
- MSDS’S (CONT’D) 20
- SECTION 3 - INSTALLATION 21
- STORAGE 22
- Rotating Assembly and Motors 22
- INSTALLATION SEQUENCE 23
- EQUIPMENT HANDLING 24
- EQUIPMENT HANDLING (CONT’D) 26
- Liquid Discharge 29
- Solid Discharge Chute 29
- EQUIPMENT LEVELING 29
- FEED AND FLUSH CONNECTIONS 31
- COMPRESSED AIR 33
- FEED PUMP 33
- ELECTRIC POWER CONNECTIONS 33
- Connection Options 33
- POLARITY TEST 36
- SENSOR CONNECTIONS 37
- MACHINE STARTUP 38
- GENERAL 39
- SOFTWARE VERSION 39
- OPERATING SAFETY 39
- Purge System Bypass 40
- INITIAL STARTUP 41
- INITIAL STARTUP (CONT’D) 42
- OPERATING INSTRUCTIONS 43
- NORMAL STARTUP 44
- COLD CLIMATE STARTUP 45
- OPERATION 45
- Bowl Speed 47
- Conveyor Differential Speed 47
- Pond Depth 47
- Pond Depth (Cont’d) 48
- BEARING TEMPERATURES 50
- MOTOR TORQUE TREND 50
- SYSTEM DIAGNOSTICS 51
- PERFORMANCE STATUS 51
- ALARM AND FAULT MESSAGES 52
- VFD STATUS 53
- VFD STATUS (CONT’D) 54
- PUMP VFD FAULT STATUS 54
- VFD TEMPERATURE TRENDS 55
- VFD FAULT RESET 55
- VFD FAULT RESET (CONT’D) 56
- SETUP SCREEN 56
- PUMP SETUP SCREEN 57
- CLEAN OUT 57
- CLEAN OUT (CONT’D) 58
- Automatic Cleanout 58
- Manual Cleanout 58
- NORMAL SHUTDOWN 59
- AUTOMATIC SHUTDOWN 59
- Excessive Vibration 59
- Main Bearing Temperatures 59
- Excessive Bowl Speed 60
- Conveyor Clutch Trip 60
- EMERGENCY SHUTDOWN 61
- Electric Power Shutdown 61
- Mechanical Shutdown 61
- SECTION 5 - MAINTENANCE 63
- PREVENTIVE MAINTENANCE 64
- LUBRICATION CHART 65
- GEARBOX OIL LEVEL CHECK 65
- GEARBOX OIL CHANGE 66
- DRIVE BELT REPLACEMENT 67
- PURGE SYSTEM 69
- Bypassing Purge System 69
- Initial Purge Time Setting 70
- Leakage Compensation Test 71
- Rotating Assembly Removal 73
- Cleaning and Inspection 75
- Installation 76
- RECOMMENDED SPARE PARTS 77
- TROUBLESHOOTING 79
- Troubleshooting Procedure 79
- TROUBLESHOOTING (CONT’D) 80
- Troubleshooting Chart 80
- CONTROL COMPONENT INDICATORS 98
- MAINTENANCE 100
- DE-7200VFDCentrifuge 103
- CONTROL ENCLOSURE ASSEMBLY 141
- DE-7200 EX-PROOF 460/480/60/3 141
- 16472-00-002 141
- DE-7200 EX-PROOF 380/400/3 143
- 16472-00-003 143
- DE-7200 EX-PROOF 575/600/60/3 145
- 16472-00-004 145
- DE-7200 460/480/60/3 147
- 16472-00-005 147
- PURPOSE 149
- DE-7200VFDCentrifuge 150
- INSTALLATION 156
- HMI Server Installation 156
- Electric Power Connections 156
- Ethernet Connections 157
- Appendix A-HMIServerSystem 158
- OPERATING HMI SERVER 159
- Startup and Shutdown 159
- Operation 159
- Operation (Cont’d) 160
- REFERENCE DRAWINGS 164
Relacionado con productos y manuales para Barebones Pc / Estación De Trabajo AOpen DE7200 Series
(11 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales